Some Important Things You Need to Consider While Installing Magnetic Car Signs

In the vast and versatile world of car graphics, magnetic car signs are the only type that can be installed and removed from your vehicle whenever you want to. The backing of magnet latches on the metallic surface of the car, van or truck and personal information or advertising message can be printed on the surface of these signs so that it is visible to passers-by. Magnetic car signs are very popular in Brisbane and their installation method is also quite simple. But there are a few things that you need to be keep in mind while installing them if you want to increase their life.

Pre-Installation Preparation

Before installing a magnetic car sign, make sure that the surface of your vehicle is dry, clean and waxed properly.

Installation

Place the edge of the sign at the desired position on the vehicle’s exterior surface and allow the adjacent part to slowly come into contact, till the whole sign is held in place. Do not attempt to rotate or pull the sign while it is attached to the car as it may damage the paintwork or stretch the sign. Try not to place it over molding or trim. There should be no air pocket between the magnet and the surface it lies on.

Cleaning and Maintenance

Consider cleaning the signs once in every week using tepid water and some mild detergent. Dry them after cleaning with a piece of soft cloth. Weekly maintenance is essential as moisture, chemicals or dirt can sometimes get trapped under the signs, and they can harm the clear coat or vinyl surface of your car. Inspect the car carefully for any change in its finish because of the sign. A gentle waxing of the car as well as of the sign’s magnetic backing will prevent any damage.

Storing

In order to prevent your signs from breaking or cracking up, do not crease or fold them. One of the most suitable places for storing them is the lining of your refrigerator. For removing slight curls in the signs, place them under direct sunlight on a flat area. However, don’t let them become overheated.

Car Wrap Designing Tips – – Car Signs Brisbane

Designing a car wrap is quite different from a typical graphic design project. In order to make sure that everything goes perfectly with the design, here are some tips from Car Signs Brisbane, an expert who is into designing, manufacturing and installing car wraps in Brisbane for years. Have a look at them. Car Signs Brisbane always follow them when designing car wraps:

They never start to design before getting the template and photos of the car that is to be wrapped. They make sure that all the obstructions along with the additions are in the right spot as well as accounted for on the template. The main purpose of the dynamic wrap is to get the info of the company out there. So, they always make it sure that the information isn’t being distorted or blocked.

The experts never assume that the full car can be wrapped. Their designing team always works together with their installation team to ensure that what they design is feasible. Since a car wrap is basically a moving billboard, people usually view the car as a whole. With regards to this, Car Signs Brisbane remembers one of the most important things while designing-that the car is a three dimensional object, which can be viewed from all the sides. So, what they do even when the designing is done one side at a time is that they think about how the side of the wrap design will connect to back side and so on.

The designing professionals never place smaller texts over the grooves or creases on the car. They place the smaller text in flat, smooth areas. This means when they use smaller text in their design, they ensure it is in a spot on the car, which keep the text from being distorted. Generally, the flat area on the door is a great place for a small text. If small texts are placed in a bump, crease or groove, they actually become unreadable and distorted.

There is also another important thing that the car wrap designing experts keep in their mind. They never use fonts just because they look cool. They make use of fonts that can be read clearly even from a distance. They know that audiences usually pass by the car at a quick speed and so if the font is unreadable, the vehicle graphics designed and installed will become useless. Display fonts actually involve a lot of fun.

How to Maintain and Store Magnetic Car Signs?

There are many companies in Brisbane, Gold Coast, Sydney and other cities of Australia that uses supreme quality magnetic materials for bringing the best in mobile magnetic advertising. Correct preparation of the surfaces and installation of these signs on vehicles is the responsibility that is taken by these professional companies. They put their best in preparing the surface area for installing magnetic car signs in the best possible manner. They also give special emphasis on the installation part being updated about the tips and techniques for magnetic car signs installation. But most of these companies make sure not to take the responsibility of the maintenance and storage of these car signs after they have been installed. If you are having plans of installing magnetic car signs in your vehicle, here are these two most important things that you need to take care of-its maintenance and its storage.

How to Maintain Magnetic Car Signs?

A magnetic car sign should be removed weekly by lifting it from center of two opposite sides. One must never start at corners because that may stretch the material. If it’s a cold weather, the sign should be preheated with warm water before removal if needed. After the signs are removed, the sign surfaces as well as the vehicle must be washed and dried. This keeps the moisture from collecting between signs and vehicle surface, which has the ability to damage the finish of the vehicle. For cleaning the signs, sponge and mild soapy water solution needs to be used. But the signs should never be immersed in water, steam cleaned or taken through car wash. After a snowfall or rain, the car magnetic car signs always need to be removed or wiped dry.

How to Store Magnetic Car Signs?

Magnetic signs must be stored either on an even, flat surface or rolled up around the cylinder with a diameter of about three inches. They should never be stored in a hot vehicle because they can warp permanently. The signs should not be folded as that may damage the material. Creasing may be formed. Any heavy object on top of the signs should never be placed. This kind of treatment prevents the signs from retaining their full magnetic function. If a sign gets bent out of the shape, all you need to do is straighten it by placing it on a flat metal surface like a refrigerator or a file cabinet. If the sign cannot be straightened, you should replace it.

Want to Wrap Your Car? Things You Should Know Before Getting It Done?

What do you mean by a car wrap?

A car wrap is basically a decal or a vinyl graphic on a car. It is put directly over the original paint of the car. The application of car wrap enables one to change the appearance of a car in a very short time. However, if need arises, the car can be returned back to its original condition by removing the wrap.

What is involved in a car wrap?

Car wraps in Brisbane basically comprises of three phases. First phase is the design phase. This includes getting the exact measurements of the car and the application of actual design of graphics. The second phase is the production phase. Here the graphic gets printed and then laminated for protecting the vinyl from UV rays and abrasions, which if not done may cause the graphics to fade with passage of time. The third phase is the installation stage. In this stage, vinyl is basically applied to the car. However, in a few cases, there is even the fourth stage which involves removal of graphics if needed.

What is difference between a full and partial wrap?

Anything that’s less than a full wrap is actually a partial wrap. A half partial wrap includes the full rear part of the car and halfway up the car and includes hood logo. Three-quarters partial wrap includes the full rear part of the car and most of the way up the car. It includes a hood logo as well. A full wrap on the other hand is basically the wrapping up of the entire surface of the car.

How long does a car wrap stay?

Generally it depends upon the quality of the vinyl graphic that is used on the car. But normally, it can be there on the car for a maximum of five years.

Does a car wrap damage the paint of a car?

No. Mostly, a car wrap doesn’t damage the paintings of a car. Actually, the wraps do not stick to the rust. If the car has a chipping paint, the wrap has the probability of pulling the chipping paint while being removed.

Is a car wash essential before installation?

Yes. The car has to be free of mud, dust, oil, wax or any other kind of product or agents, which can prevent the vinyl from adhering to the surface of the car during the process of installation.